So I need a 1310 U joint diff flange.

Where do I get one?

-Mike

Quote
Michaelb
So I need a 1310 U joint diff flange.

Where do I get one?

-Mike

Ben thinking of a separate "Get your Toiletta flange and u-joint" thread..
The big deal is getting the "weld yoke", the other half of the u-joint assembly that welds into he rear tube..

But again, makes sense for me to order 7-10 at a whack...

What prop shaft do you have?

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.

I need to get my ass under the car to see what that 2pc driveshaft I have (rapido) looks like on the end. Hmm.

Quote
jbass
I need to get my ass under the car to see what that 2pc driveshaft I have (rapido) looks like on the end. Hmm.

get crawlin, slither boy!

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.

flanges are here, about 2/3 of the way down the page
http://www.driveshaftsuperstore.com/Drive_shaft_custom_flanges.htm
which flange is correct? i'm thinking the 2 3/8 square pattern?
thx

Quote
motorhead_1
flanges are here, about 2/3 of the way down the page
http://www.driveshaftsuperstore.com/Drive_shaft_custom_flanges.htm
which flange is correct? i'm thinking the 2 3/8 square pattern?
thx

We can beat that price. brouh ha ha!

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.

Quote
john vanlandingham

Quote
motorhead_1
flanges are here, about 2/3 of the way down the page
http://www.driveshaftsuperstore.com/Drive_shaft_custom_flanges.htm
which flange is correct? i'm thinking the 2 3/8 square pattern?
thx

We can beat that price. brouh ha ha!

How much shipped to 85210? Thx

I'll hold onto a set...thought you were Jeff Esteban. Hardware is on the way, I just have to make sure I have enough for myself and those that have paid. $25 shipped for the whole set. I'll definitely have more of the CV adapter hardware than DS hardware. Exact number will be posted when I get them. Will be within the next couple days.

So its too late to srnd monry for cv and ds hardware? Can anyonr just share the the thread sizes and bokt lengths so I can just order stuff?

Quote
espacef1fan
So its too late to srnd monry for cv and ds hardware? Can anyonr just share the the thread sizes and bokt lengths so I can just order stuff?

Well, the guy sent the box to one of my old SD addresses, so it got sent back to him (thank God it's not lost). He'll resend it. I should have another set of DS hardware. I am positive I have the CV hardware. Once I get it I will make a post.

I have a few different driveshafts, what would you need to know the ID of the tube?

-Mike

Quote
Michaelb
I have a few different driveshafts, what would you need to know the ID of the tube?

-Mike

yeah, I do too but been too busy to dig one out and hacksaw it in half and clean the burrs and measure ID, OD, and wall. If you cut by the weld then its ready for the weld yoke to get welded in..

Post what you see.

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.

Good news!
I asked once again---about the 6th time----at Tacoma Screw wherre I buy hardware and this time they actually walked and looked and found M10 x 1.25 nuts with 14mm hex for the Toyota CV flange nuts so I cleaned them out. Got 42 so thats 3 full sets...and a few extree.

Now maybe its smartest I send them with like Adam's diff covers or the Flanges that some youse galoots need.
We gotta get this figured out so I don't spend hours searching just for miserable little nuts.

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.

Hey John, I know that I am now being a pain in the A$$, but could you hook me up with a 1310 U joint diff flange and a set of the CV shaft nuts? No need to ship as I plan to be there Dec 10, +-3 days...when I know for sure I will call you. This time I am going to drop in, kick parts/tires and chew the fat...Might even be heading to Beijing for a few days through Seattle.
FYI, roundtrip with Delta SeaTac to PEK(Beijing) is $660 right now! Insane cheap...
Let me know if you want anything from Kanuckistan.
Tomi

Quote
TomiHulk
Hey John, I know that I am now being a pain in the A$$, but could you hook me up with a 1310 U joint diff flange and a set of the CV shaft nuts? No need to ship as I plan to be there Dec 10, +-3 days...when I know for sure I will call you. This time I am going to drop in, kick parts/tires and chew the fat...Might even be heading to Beijing for a few days through Seattle.
FYI, roundtrip with Delta SeaTac to PEK(Beijing) is $660 right now! Insane cheap...
Let me know if you want anything from Kanuckistan.
Tomi

Naw man only thing I'm worried about is I made like 18 hats for disc brake deals cause you said you and 2 other wanted front kits...and i order calipers too...
I'll get some stuff and set it aside so then you'll have to stop in..

Watcha got going in Beijing? You know what? They NEED some strong unions in the PRC now, gonna organise?


As for what I NEED from Canada, I need 2-3 Institutional size--bigger than fambly sized---bottles of HP Sauce...

it's one of the few things that substantially cheaper there....poooooor me!!!

---

John Vanlandingham
Sleezattle, WA, USA

Vive le Prole-le-ralliat

www.rallyrace.net/jvab
CALL +1 206 431-9696
Remember! Pacific Standard Time
is 3 hours behind Eastern Standard Time.